Jotun Paint Essence Cover Plus For Interior 15L (Matt - Standard Colour)

Description
• Essence Cover Plus is specially formulated with washable feature that ensures stubborn stains can be easily wiped away from interior walls.
• Comes with enhanced hiding power to cover wall surfaces imperfections, and better flow to give your wall a smooth and even finish.
   - Easy Clean
   - Smooth Finish
   - Good Hiding
   - Low Odour & Low VOC
   - Easy To Apply
• Essence Cover Plus is a washable paint with easy clean properties, comes with enhanced hiding power & good flow for a smooth finish in just 2 coats.

Specifications
• Application equipment / methods: By brush, roller, airless spray or conventional spray.
• Guiding data for airless spray
   - Nozzle tip 0.021–0.027"
   - Spray angle degrees 65–80°
   - Pressure at nozzle 140 - 190 kg/cm² (2100 psi)
• Spreading rate per coat
   - Theoretical 12.3 m²/l - 9.3 m²/l
   - Spreading rate depends on film thickness applied, type of texture, surface porosity, imperfections, temperature, wastage during painting etc.
• Recommended film thickness per coat
   - Wet 81 µm - 108
   - Dry 30 µm - 40 µm
   - Film thickness will vary and is calculated as average.
• Thinner: Water
• Dilution: The paint is ready to use after proper stirring. If thinning is required, water may be added up to a maximum of 5%.
• Conditions during application
   - Apply at a temperature between 10°C - 35°C.
   - The temperature of the substrate should be minimum 3°C above the dew point of the air. The temperature and the relative humidity should be measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper drying.
• Drying times
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with:
   - Good ventilation (Outdoor exposure or free circulation of air)
Typical film thickness
   - One coat on top of inert substrate
   - The given data must be considered as guidelines only. The actual drying time and time before recoating may be shorter or longer, depending on the ambient temperature, film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc.
1. Recommended data given is, for recoating with the same generic type of paint.
2. In case of multi-coat application, drying times will be influenced by the number and sequence and by the total thickness of previous coats applied.
3. The surface should be dry and free from any contamination prior to application of the subsequent coat.
The drying time is measured by stated values:
   - Relative Humidity (RH): 50 %
   - Substrate temperature: 10 °C
      - Surface (touch) dry: 2 h
      - Hard dry: 8 h
      - Dry to over coat, minimum: 4 h
   - Substrate temperature: 23 °C
      - Surface (touch) dry: 1 h
      - Hard dry: 6 h
      - Dry to over coat, minimum: 2 h
   - Substrate temperature: 40 °C
      - Surface (touch) dry: 0.5 h
      - Hard dry: 4 h
      - Dry to over coat, minimum: 1 h

Features and benefits
• Easy Clean - Stubborn stains on the wall can be cleaned easily.
• Good Hiding - Provides good hiding power to conceal wall imperfections.
• Smooth Finish - Better flow for smooth and even finish.
• Low Odour - Paint odour is low during and after application making the property ready for occupancy in shorter period.
• Low VOC - Pass international & local green coating standards.
• Easy to Apply - Effortless application with smooth finish.
• Formulated Without Harmful Chemicals - Free from harmful chemicals and emissions such as APEO, formaldehyde and heavy metals.

Type
An interior acrylic emulsion paint that gives good washability, smooth finish and good hiding. Available in Matt finish.

Recommended use
For interior application, suitable for new buildings and repainting.

Substrate
On concrete, masonry, plaster, brick work and soft board surfaces.

Directions for use
Surface preparation
• The substrate must be sound, clean, dry, free from dust, oil, grease and laitance etc. All traces of release agents must be removed. On chalky and dusty surfaces, all loose material must be removed by stiff bristle brushing.
• Other surfaces: The coating may be used on other substrates.
Please contact your local Jotun office for more information.
• Primer: Jotun Essence Easy Primer:1 coat
• Topcoat: Essence Cover Plus Matt(MY):2 coats
Recommended paint system
• Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care.

Disclaimer

All product images shown are for illustration purposes only. Actual products may vary in term of size, type, brand, version, colour, and other relevant characteristics.