Menu
Your Cart

Corkjoint CJ-100 Adhesive Hydrophilic Rubber Waterstop (Accessories) 3.6 litre

Corkjoint CJ-100 Adhesive Hydrophilic Rubber Waterstop (Accessories) 3.6 litre

RM122.04
Price in reward points: 48800
Products Sold: 0
Product Views: 1569
Add to Cart
Click to share this page to your friends & families and start earning. Affiliate

SPECIAL ORDER Special Orders require 7 to 14 working days to be ready for collection or delivery and some products might take longer to order in. Please contact us for more information or estimated delivery time before placing your order. 

  

Description 

CORKJOINT CJ-100 Adhesive is a premium quality solvent-based synthetic rubber resin adhesive formulated to bond variety of common materials. It has high viscosity, short tack time, is easy-too-apply, offers superior bonding strength and cost savings. CJ-100 Adhesive is used to install Corkjoint's range of hydrophilic waterstops and expansion joint fillerboards. 

  

Coverage 

  

Applications 

Suitable for bonding rubber, cork and closed-cell polyethylene to concrete surfaces. 

  

Product Specification 

PROPERTYTYPICAL PROPERTIES
AppearanceLight Brown Yellowish Liquid High Viscosity Liquid
Viscosity At 30°C7,000 - 8,000 CPS
Solid Content28 - 32%
Application Temperature-10°C to 40°C
Service Temperature-10°C to 60°C
Shelf Life12 months from date of manufacture
Main SolventHydrocarbon Solvent
Main IngredientChloroprene Rubber
DilutionToluene

  

Cautions 

  • Avoid contact with eyes, skin and mouth.. 
  • Use in a well ventilated area. In case of contant with eyes, flush with water immediately for 15 minutes. If irritation persists, seek medical attention. Keep out of reach of children. A material safety data sheet is available upon request.. 

  

Storage 

  • Highly inflammable, keep away from heat source or natural flames.. 
  • Store in a dry and cool place with temperature below + 25°C.. 
  • Use within 12 months from date of production.. 

  

Application Procedures 

  1. Surface must be clean, dry and free of dirt, grease oil & water.. 
  2. Stir adhesive thoroughly before use.. 
  3. Apply the adhesive to both surfaces to bonded with a dry, clean brush or scraper to give a uniform coating.. 
  4. Allow the solvents to evaporate until adhesive film is "tacky" or "touch dry". It will take between 10 to 20 minutes depending upon the surface porosity and the weather conditions.. 
  5. Position the coated surfaces accurately before assembling them and upon installation, apply an even pressure to the installed material to consolidate the bond.. 
  6. Bond strength can be fully obtained after 24 hours.. 

  

Health And Safety Information 

  • Do not apply highly flammable adhesive near smoke or naked flame. In case of fire, extinguish with carbon dioxide, dry chemical or foam fire extinguisher.. 
  • As with all construction chemical products caution should be exercised.. 
  • Protective clothing such as gloves and goggles should be worn.. 
  • Treat any splashes to the skin or eyes with fresh water immediately.. 
  • Should any of the products be accidentally swallowed, do not induce vomiting, but call for medical assistance immediately.. 

  

Hazard Identification 

  

Signal Words: Danger 

Hazard Description: Highly flammable. May cause sensitizations by skin contact, irritating to eyes, respiratory system and skin. Harmful by inhalation, in contact with skin and if swallowed. 

Safety Description: Keep out reach of children. Keep container in a well-ventilated place. Keep away from sources of ignition- NO SMOKING 

  

 

  

Disclaimer
All product images shown are for illustration purposes only. Actual products may varies in term of size, type, brand, version, colour, and other relevant characteristics.